ENCAD T-200 Anleitung zur Fehlerbehebung Seite 12
- Seite / 91
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Printer Setup 1-3
ENCAD
®
T-200
TM
Reference Guide
Encad inks and media give you optimal image quality through:
• Scientifically matched ink and media
• Bond, Mylar, Vellum and Premium Matte.
Caring for your ink, cartridges and caddies
• Handle cartridges only on the plastic areas. Touching the copper electrical interconnect
or the inkjets can damage the cartridge.
• Do not mix inks.
• Do not shake ink containers.
• Store ink, cartridges and caddies in the same environment as the printer, whenever
possible.
• If you remove a cartridge from the printer, do not leave it exposed to the air for an
extended period because the jets may clog. Remove the Ink Caddy and replace the
original tape on the jet plate. Place the cartridge in a cartridge garage or sealed plastic
bag and store it in a closed area at room temperature. Keep it out of direct sunlight.
• Open new cartridges only when you are ready to install them.
• Use only Encad-brand ink refills and cartridges.
• Drawings containing both black and color elements require alignment of the cartridges
to each other as described later in this chapter.
CAUTION: Ink caddies can be affected by large temperature swings. In uncontrolled
environments, large temperature swings, ranging from 10° to 20°F (5.6° to 11.2°C), can
cause small amounts of ink to drip from the cartridge. Caution should be exercised to
control the environment to minimize temperature swings.
WARNING: Do not operate the printer when an ink caddy is out of ink. This could
cause premature cartridge failure. Replace caddies when the ink level reaches the line
printed on the caddy label.
Choose the right media
You can rely on Encad media for rich, vivid images across the entire color spectrum. Our
media is specially formulated to demanding specifications, strict performance criteria,
and uncompromising quality controls. This assures superb interaction with ENCAD CIS2
ink and flawless performance with the printer.
- Printer Reference Guide 1
- WARRANTY CLAIMS 2
- FCC Statement (U.S.A.) 3
- VDE statement 4
- Industry Canada 4
- Material safety data sheet 4
- General operating safety 5
- Manual conventions 5
- Other reference materials 6
- Contents 7
- EFERENCE GUIDE 8
- Printer setup 1 10
- Printing 11
- Obtaining quality results 11
- Use the right inks and media 11
- Choose the right media 12
- Caring for your media 13
- Use the right software 13
- Status LEDS 14
- Selection 14
- Choosing menu functions 15
- Setting the language 15
- To choose a language 15
- To choose supply type 15
- Loading media 16
- To load media 16
- Feed media 16
- To feed media 16
- Moving the carriage 17
- To move the carriage 17
- Installing the cutter 17
- To install the cutter 17
- ➪ To print the color test 18
- Printing the prime pattern 19
- To print the prime pattern 19
- Clogged jets 20
- Cleaning jets 21
- To use the clean function 21
- Manual jet compensation 21
- Aligning the ink cartridges 22
- Performing color calibration 24
- To perform color calibration 24
- Paper axis calibration 25
- Cartridge recognition 26
- Installing software 27
- Windows driver 27
- To install the Windows driver 27
- HDI version 6 and 7 drivers 28
- ADI driver 29
- To install the ADI driver: 30
- Network considerations 31
- Making a test print 31
- Canceling a print 31
- Printer options 2 32
- LED display 33
- Printing the settings 34
- Choosing print mode options 34
- Color mode 35
- To choose the color mode 35
- Quality modes 35
- To choose print quality 36
- Resolution 36
- To choose resolution 36
- Choosing paper options 37
- Media supply 37
- Media standard 37
- To choose the media standard 37
- Printer Options 2-7 38
- Reference Guide 38
- Printer Options 2-8 39
- Printer Options 2-9 40
- Printer Options 2-10 41
- Printer Options 2-11 42
- To set margins 43
- Auto-Cut 43
- To set Auto-Cut 43
- Save Media 43
- To turn off Save Media 43
- Auto-Wipe 44
- To turn off the wiper 44
- Defining user setup 44
- To save user setup 44
- Defining units of measure 45
- To choose measurement units 45
- Choosing a language 45
- ➪ To set the ink preheat time 46
- ➪ To set the dry time 47
- Printer Default Settings 48
- Printing a file 49
- Heidi driver 49
- Device and document settings 50
- Custom properties 51
- Printing 3-4 52
- Stopping printing 54
- Spooling 54
- HP-GL/2 options 4 55
- Accessing HP-GL/2 features 56
- To access HP-GL/2 features 56
- Palette select 56
- To choose a palette type 56
- ➪ To set control 57
- To rotate the image 58
- Ink reduction 58
- To set ink reduction 58
- Rotation 58
- Reprints 59
- To make multiple prints 59
- ➪ To enable nesting 60
- Nest time 61
- To define nesting time 61
- Ink limit 61
- To enable the ink limit 61
- HP-GL/2 Test File 62
- To print the test file 62
- Acceptable DIMM sizes 63
- DIMM installation 63
- To remove the right cover 64
- To remove the DIMMs 64
- ➪ To install the new DIMM 65
- Menu tree B 66
- Setup menu at a glance 67
- Setup menu 68
- User Setup 69
- Ink Options 69
- Utility menu at a glance 70
- Utility menu 70
- Color Calib 71
- Db Calib 71
- Paper Calib 71
- Display Settings 71
- Print Settings 72
- Service Menu 72
- Open Jets 72
- Technical information C 73
- Technical information C-2 74
- REFERENCE GUIDE 74
- Cartridge errors 75
- Memory Errors 76
- Troubleshooting E 77
- Printer Health 78
- Encoder Strip 80
- Trailing Cable Shelf 80
- Data Transfer 86
- Application Software 88
- Calling for Help 90
- Customer Technical Support 91
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.062 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern